Auto-Foam - 5000ml
- Highly active snow foam
- Acid-free
- Safe for all surfaces
- Biodegradable
Auto-Foam is a premium pre-wash foam designed to optimize vehicle preparation. This water-based formula is created to remove dirt and contaminants from the paint before applying shampoo and other products like wash mitts.
It ensures a thorough clean without damaging the paint. Auto-Foam is compatible with all pressure washer and high-pressure foam lances and has an ideal PIR (Panel Impact Ratio) of 4%, as explained in the manual below. The foam remains active for five minutes to effectively perform its task.
The product is biodegradable, tough on dirt, yet gentle on paint. Its non-caustic formulation preserves the paint even with regular use. The foam breaks down gradually, allowing the cleaning agents to work and effectively remove contaminants. After use, Auto-Foam can be easily rinsed off, leaving the vehicle ready for subsequent treatments.
Not suitable for PET bottles; always rinse thoroughly after use.
| Product number: | 101252 |
|---|
Auto-Foam can be applied using a foam lance, hand foamer, or spray bottle. The minimum recommended PIR (Panel Impact Ratio) is 4%.
Follow these steps only once, and remember to record the ratio on the container for future use. Fill the mixing bottle with tap water up to the maximum level. Set the foam lance or, if using the pressure washer’s own reservoir, adjust it to the maximum product flow. Use a large empty bucket and spray with the foam lance into the bucket until the mixing bottle is empty, then stop immediately. If the bottle isn’t empty and the bucket is full, halve the amount of water in the mixing bottle and start over. All subsequent numbers should be halved accordingly.
To achieve a PIR of 4%, measure the total liters in the bucket after the mixing bottle is empty. Multiply this number by 0.04 to determine the amount of product needed for the mixing bottle. Mix the bottle with the calculated amount of product and water. Foam the vehicle and let it sit for up to 5 minutes. Never let the product dry. Rinse off with high pressure.
Example Calculation with a Pressure Washer and a Monello Lancia Foam Lance:
- Fill the 1000 ml mixing bottle with tap water.
- Attach the foam lance to the pressure washer and set it to the maximum foam setting.
- Spray into a large empty bucket until the 1000 ml bottle is almost empty. The bucket will then contain approximately 13 liters of water.
- The required amount of product is 13 x 0.04 = 520 ml, with the remainder filled with water.
6 - 3 of 34 reviews
Hoog alkalische foam
Goede reiniging, wel veel vloeibaarder dan andere snowfoams, maar doet wel goed zijn werk. Bijna alle verontreiniging gaat er al af bij het spoelen
Goede pre-wash
Zoals meerdere zeggen geeft deze een goede reiniging maar geen super dik schuim. In principe niet direct een nadeel maar sommige willen graag dik schuim. Ikzelf heb eens een klein beetje polar blast van Autoglym toegevoegd en dan is het schuim veel dikker en de reiniging blijft zoals zonder de polar. Op het eerste zicht tast het de beschermende lagen niet aan (coatings of wax) dus echt top
Geweldige cleaner
Zeer actieve pre-wash maakt daar door ook zeer goed schoon, ik hou kwa pir de instructie aan maar deze verlagen zou ook best kunnen. Ik spuit 2x de auto in laat per keer de schuim aflopen en inwerken daarna de hogedrukreiniger erover en maakt echt fantastisch schoon. Alle roadfilm insecten etc zijn er echt af. De coating / wax lijft zeker wel zitten daar de beading zeker aanwezig blijft. Gebruik het ook voor de motor welk wat schoner blijft na goed afspuiten is wassen soms niet eens nodig en kan meteen de wax erop.. tot nu toe nog geen betere gevonden
Shared on our socials.